Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (2022)

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (1)

When your Honda lawn mower’s engine doesn’t idle, lacks power at high speed, or won’t start, it could be time to adjust the carburetor. If you have never done this before, you are probably wondering how difficult it will be, what tools you will need, and if you should just call an expert.

Adjustments to a Honda lawn mower’s carburetor should be made after it has been cleaned. If the carb is dirty, adjustments will be temporary. You will need some screwdrivers, a wrench, a carb cleaner, and an hour or two. Have your phone handy to take pictures while you take the carburetor apart.

Keep reading to find out how a carburetor works, what could be causing different problems, as well as preventative measures.

How Does a Carburetor Work?

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (2)

Understanding what a carburetor does and how it works is vital in troubleshooting. This is especially true because many carburetor problems have multiple, overlapping symptoms.

The carburetor’s role is to provide the space where gas and air mix. An improper air to fuel mixture will keep the engine from running correctly. An incorrect gas and air mix cause most carburetor problems. Your job is to figure out what is causing the mix to be off.

  • Float Chamber: The float chamber holds fuel, and as the amount of fluid increases, the float rises until it is pushed into its seat. When fuel leaves the chamber, the float falls. As more fuel enters, it rises again.
  • Intake: Air rushes through the throat of a carburetor, and then a narrower passageway called a venturi. This causes the air to speed up, creating a vacuum that pulls fuel into the fuel nozzle.
  • Fuel Jet: Once the proper gas/air mixture has been created, the fuel is pulled through the fuel jet. This creates the explosion that powers the engine.
  • Throttle Valve: This valve controls the amount of gas that goes into the carburetor. An open valve increases the engine’s power, and a closed valve stops the engine.

Carburetor problems can occur at each of those points, and the way to fix most carburetor problems is to get inside and see which of these is causing the problem.

(Video) How To Adjust the RPM Speed on a Lawn Mower

Why You Should Clean the Mower’s Carburetor

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (3)

Although you might be tempted to play around with the throttle or make other adjustments, clean the carburetor. Otherwise, any corrections you make will be temporary, and you could wind up causing even more damage to the carb.

Also, get a parts cleaner, such as WD-40 Specialist Carb/Throttle Cleaner. It contains the solvents you need to clean out the gunk, and the spray will blast away dirt and deposits. For tools, you will need screwdrivers and a socket wrench.

Mower Engine Starting Problems

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (4)

If your engine is not starting, you have difficulty starting it, or it stops after you get it started, then the following could be causing starting problems:

  • The main jet, main nozzle, or main nozzle air path could be clogged.
  • The float isn’t moving correctly.
  • The throttle stop position is wrong.

Mower Speed Problems

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (5)

If the engine speed does not increase, the speed is unstable, or the engine performs poorly at high speed, then an additional clog to check for is the pilot jet—either its air path or the jet itself are clogged.

(Video) LAWNMOWER GOVERNOR ADJUSTMENT: Honda Lawn mower REVS UP TOO MUCH or NOT ENOUGH?

Should speed problems happen at low speeds or the idle speed is unstable, then in all likelihood, the pilot jet or its air path is clogged. You will need to check for dirt and clean.

Mower Gasoline Problems

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (6)

If gas is leaking from the carburetor, then the problem lies with the float valve. Either the float valve is worn out or coated with dirt, or the valve seal is worn or dirty.

Getting to the Mower’s Carburetor

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (7)

Before you get started, we recommend you disconnect the spark plug cap. This is to prevent the mower from accidentally starting. Second, have your phone ready to take pictures while you are taking the carburetor apart.

Fix Without Taking the Carburetor Apart

You might get lucky and avoid having to take the carburetor apart. To do so, focus on cleaning out the carburetor idle jet. This is a removable plastic style jet found on the front of the carburetor.

  1. First, spray the carb cleaner and remove the dirt and gunk.
  2. Look for a plastic screw with a Phillips head bolt. That’s the idle adjustment screw. Loosen and remove it.
  3. Now you will have access to a rubber plug with a hole. This is the idle/pilot jet.
  4. To remove the pilot jet, you need to pull it out gently. Use flathead screwdrivers to wedge it up.
  5. After you get it out, you should clean it with the carb cleaner. The small hole on the end often gets plugged. Honda makes Jet Cleaner sets, but a tiny pin will be a good substitute.
  6. After you have cleaned the pilot jet, push it back in carefully, and then replace the idle screw. Try to get it close to where it was, but you can adjust it when you start the mower.

Clean Out the Float Bowl

The float bowl is at the bottom of the carburetor. It is easy to take off, but before you do, turn off the fuel line. Then loosen the bolt on the bottom and take out the bowl.

There are two gaskets—one where the bowl connects to the housing, and another one on the bolt. Inspect both for cracks. Then clean out the bowl and replace the housing.

(Video) honda model hrr216k9vkaa lawn mower carburetor repair

Taking the Mower’s Carburetor Apart

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (8)

If the mower is still not running correctly, then the carburetor must be taken apart so that you can clean it. This is a much more complicated procedure and could take an hour or more.

  1. First, remove the air filter. If it is dirty, replace it. A dirty air filter can affect how well your mower runs better. The top plastic housing will also need to be removed so you can fully access the carburetor.
  2. Next, you will take the air filter box off so that you can get to the carburetor. In most models, it is held on by two bolts. As you loosen the bolts, hold onto the carburetor. The bolts run through the carburetor and mount it to the motor housing.
  3. Now that you have access to the carb, get ready to start taking pictures. Anything you unhook needs to be hooked back correctly. Keep an eye out for the tiny spring attached to the top.
  4. Once you have taken the carburetor off, it is time to disassemble. As you do so, check the gaskets—worn ones need to be replaced. Continue taking the carb apart and cleaning. Every hole needs to be clear of dirt.

Finally, the carburetor will have to be reassembled. Hopefully, you took lots of pictures so that you have them as guides.

Rather than taking a carb apart, some folks simply buy a new carburetor.Be sure to check compatibility with your Honda Mower.

Check out this 12-minute video that will take you through the steps of fixing a lawn mower carburetor:

Fuel Recommendations for Honda Small Engines

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (9)
(Video) How to get your lawnmower ready for spring. Honda HRB216

To prevent future problems, make sure you are following Honda’s recommendations. Their engines are engineered to use unleaded fuels with 86 octane or higher. Ethanol fuels can be used as long as the fuel has no more than 10% ethanol (E10). A fuel with methanol should contain no more than 5% methanol.

Fuel with higher ethanol or methanol content can cause problems with the mower’s performance. The engine’s warranty does not cover damage to the engine caused by fuel with more than 10% ethanol.

If possible, regular unleaded gasoline is ideal. Avoid E85 at all costs because Honda considers it an alternative fuel since it is 85% ethanol and only 15% gasoline.

Storage Suggestions to Prevent Carburetor Problems

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (10)

These are some suggestions to prevent future carburetor problems. Gasoline can begin to deteriorate within three to four weeks, so use these if you only mow every couple of weeks:

  • Fill up the tank. As fuel is exposed to heat or air, it oxidizes and can gum up the carburetor’s jets. Keep the tank full to minimize how much gas can enter the tank through the vent.
  • Run the engine out of gas. No fuel = no oxidation. If the mower only has a little gas in the tank, run it dry and close the fuel valve.
  • Storage container. Make sure you close the container tightly and store it in a cool place. Honda discourages metal fuel containers since they might rust, and tiny rust particles can clog the carburetor.
  • Fuel Stabilizer. Fuel stabilizers should be added if gas is stored either in the container or the mower for three months or longer. If you plan to use the mower within a year, there is no need to drain the gas from the fuel tank or carburetor—as long as you add the stabilizer.

Final Thoughts

Carburetors are an essential and often overlooked part of a lawn mower. If your mower is not running well and you have checked the air filter and spark plug, you might have to work on the carburetor. Taking the carburetor apart and cleaning it is time-consuming but not difficult. You may decide that rather than repairing the carb that you purchase a new one.

Related Articles

Honda Lawn Mower Carburetor Adjustment: How to Do It - Ready To DIY (11)
(Video) honda hrx 217 lawn mower carburetor repair clean fix rebuild

Honda Lawn Mower Won’t Idle

Why Does My Honda Lawn Mower Backfire?

FAQs

How do you adjust the carburetor on a Honda lawnmower? ›

Honda Lawn mower REVS UP TOO MUCH or NOT ENOUGH? - YouTube

How do you adjust a Honda carburetor? ›

GX160 Governor & Carburetor Speed Adjustments - YouTube

How do you adjust the air fuel mixture on a lawn mower? ›

How to Adjust The Carburetor On A 4- Cycle Engine in 2 Minutes - YouTube

Does a new carburetor need adjustment? ›

Even if a carburetor is brand new, it still needs tuning. Your engine, its condition, your location, and the weather all come into play and the carburetor needs to be adjusted properly.

How do I know if my carburetor is rich or lean? ›

If the mixture is too lean, it will leave no color, while a rich mixture will cause the fuel ring to become more prominent. Over-rich mixtures will give the plug a sooty appearance.

How do I know if my carburetor needs adjusting? ›

The engine should rev smoothly and quickly as soon as you apply throttle. If the vehicle is displaying any sort of sluggish performance or misfires when you apply the throttle, then more adjustments are required.

What are the two adjustment screws on a carburetor? ›

Find the adjustment screws on the front of the carburetor.

There should be two screws on the front of the carburetor, which are used to adjust the air and fuel mixture. Often these look like flat-head screws and you can use a screwdriver to turn them, adjusting the amount of fuel and air mixing in the carb.

What is the best air-fuel ratio for a carburetor? ›

The ideal chemical air-fuel ratio, in which all the fuel is oxidized, is 14.7:1, that is, 14.7 parts air to 1 part fuel. A “rich” condition means more fuel is being used, an air-fuel ratio less than 14.7, while a “lean” condition means less fuel is being used, an air-fuel ratio higher than 14.7.

How do you adjust the fuel mixture on a Briggs and Stratton? ›

Carburetor adjustment for Briggs and Stratton engine - YouTube

How do you adjust the carburetor on a Briggs and Stratton lawn mower? ›

How to Adjust a Briggs & Stratton Carburetor - YouTube

How do you adjust a running rich carburetor? ›

Regardless of whether or not the engine is running too rich or too lean, bring it down to a very lean mixture by turning both screws a quarter-turn at a time, counter-clockwise, then slowly bringing them back up to an equal and smooth mixture.

Which way do idle mixture screws turn? ›

On most carburetors, turning the mixture screw in (clockwise) leans the mixture, while counterclockwise (out) enriches the mixture. Initially, if the engine stumbles or the vacuum drops when turning the mixture screw in, turn both screws out about a -turn and evaluate the results.

Videos

1. Honda Mower Surges
(Veteran's Small Engine Repair)
2. How to Adjust Idle and RPM on Lawn Mowers with automatic throttle
(Parts Counter Gurus)
3. Throttle Adjustment, Honda Mower
(Veteran's Small Engine Repair)
4. Honda Lawnmower Won't Idle (Service Carburetor And Set Valves)
(Mower Man)
5. Lawnmower service - Step by step / Including carburetor cleaning (HONDA)
(Turners Workshop)
6. Make Your Lawnmower Start On The First Pull Again - Honda Auto-choke Repair - Video
(donyboy73)

Latest Posts

Article information

Author: Pres. Carey Rath

Last Updated: 11/18/2022

Views: 6107

Rating: 4 / 5 (41 voted)

Reviews: 88% of readers found this page helpful

Author information

Name: Pres. Carey Rath

Birthday: 1997-03-06

Address: 14955 Ledner Trail, East Rodrickfort, NE 85127-8369

Phone: +18682428114917

Job: National Technology Representative

Hobby: Sand art, Drama, Web surfing, Cycling, Brazilian jiu-jitsu, Leather crafting, Creative writing

Introduction: My name is Pres. Carey Rath, I am a faithful, funny, vast, joyous, lively, brave, glamorous person who loves writing and wants to share my knowledge and understanding with you.